Mamba3D Configuration Permanent Future Lab Seats2meet.com Utrecht CS

From Permanent Future Lab

Paste this into an config-bundle.ini file and import this in Repetier Slic3r. Note that 'print speed' in repetier is a manual setting and not part of the config file. The bed level offset needed can deviate from the one mentioned in the config settings. 


# generated by Slic3r 1.2.9 on Wed Feb  8 13:24:10 2017

[filament:ABS_1.75_w_HeatedBed]
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 70
first_layer_temperature = 250
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 250

[filament:Flexible PLA]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 3
first_layer_bed_temperature = 0
first_layer_temperature = 240
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 240

[filament:High_Temp_PLA_1.75]
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 75
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 205

[filament:Low_Temp_PLA_1.75]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 0
first_layer_temperature = 195
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 200

[filament:PLA_1.75]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 0
first_layer_temperature = 195
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 195

[filament:PLA_1.75_w_HeatedBed]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 50
first_layer_temperature = 195
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 195

[filament:XT_1.75_w_HeatedBed]
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 70
first_layer_temperature = 250
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 250

[filament:khalid]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1.01
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 0
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 15
slowdown_below_layer_time = 15
temperature = 215

[filament:tst-filament-adhesion]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 3
first_layer_bed_temperature = 0
first_layer_temperature = 220
max_fan_speed = 70
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 195

[filament:tst-luminous]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 3
first_layer_bed_temperature = 0
first_layer_temperature = 220
max_fan_speed = 70
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 220

[presets]
filament = PLA_1.75.ini
print = 3_High_Res_Med_Speed.ini
printer = Config_Mamba3D_AutoLevel.ini

[print:1_Low_Res_Med_Speed]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 20
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 75%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = line
first_layer_acceleration = 0
first_layer_extrusion_width = 100%
first_layer_height = 0.3
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 80
interface_shells = 0
layer_height = 0.295
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 3
skirt_height = 1
skirts = 1
small_perimeter_speed = 50%
solid_infill_below_area = 1
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 80%
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 40
top_solid_layers = 4
travel_speed = 150

[print:2_Med_Res_Med_Speed]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 20
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 75%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = line
first_layer_acceleration = 0
first_layer_extrusion_width = 100%
first_layer_height = 0.3
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 80
interface_shells = 0
layer_height = 0.195
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 3
skirt_height = 1
skirts = 1
small_perimeter_speed = 50%
solid_infill_below_area = 1
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 80%
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 40
top_solid_layers = 6
travel_speed = 150

[print:3_High_Res_Med_Speed]
avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 20
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 75%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = line
first_layer_acceleration = 0
first_layer_extrusion_width = 100%
first_layer_height = 0.25
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 2
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_height = 0.105
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 3
skirt_height = 1
skirts = 1
small_perimeter_speed = 50%
solid_infill_below_area = 1
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 80%
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 70%
top_solid_infill_speed = 40
top_solid_layers = 8
travel_speed = 150
xy_size_compensation = 0

[printer:Config_Mamba3D]
bed_shape = 0x0,200x0,200x200,0x200
end_gcode = M104 S0 ; turn off temperature\nG1 X200 Y200 F4000\n;G28 X0  ; home X axis\nM84     ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 0
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
start_gcode = M109 S[first_layer_temperature]\nG28\nG92 E0\nG1 E10 F100\nG1 Z5 F100\nG1 X0 Y0 F2500\nG1 Z0 F100\nG92 E0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:Config_Mamba3D_AutoLevel]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off temperature\nG1 X200 Y200 F4000\n;G28 X0  ; home X axis\nM84     ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 0
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
start_gcode = M109 S[first_layer_temperature]\nG91\nG1 Z10 F500\nG90\nG28 X0 Y0\nG1 X50 Y50 F2000\nG28 Z0\nG29\nG92 E0\nG1 Z10 F500\nG1 X0 Y0 F4000\nG1 Z0 F500\nG1 E20 F100\nG1 Z5 F100\nG1 X5 Y5 F2500\nG1 Z0 F100\nG92 E0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = -0.95

[printer:Config_Mamba3D_concept]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off temperature\nG1 X200 Y200 F4000\n;G28 X0  ; home X axis\nM84     ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 0
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
start_gcode = M109 S[first_layer_temperature]\nG91\nG1 Z10 F500\nG90\nG28 X0 Y0\nG1 X50 Y50 F2000\nG28 Z0\nG29\nG92 E0\nG1 Z10 F500\nG1 X0 Y0 F4000\nG1 Z0 F500\nG1 E20 F100\nG1 Z5 F100\nG1 X5 Y5 F2500\nG1 Z0 F100\nG92 E0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = -0.93

[printer:incheckpillar]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off temperature\nG1 X200 Y200 F4000\n;G28 X0  ; home X axis\nM84     ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 0
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
start_gcode = M109 S[first_layer_temperature]\nG28\nG92 E0\nG1 E10 F100\nG1 Z5 F100\nG1 X0 Y0 F2500\nG1 Z0 F100\nG92 E0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = -1

[printer:khal]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 3
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0.1
retract_restart_extra_toolchange = 0
retract_speed = 30
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[settings]
autocenter = 1
mode = expert
Retrieved from "https://permanentfuturelab.wiki/w/index.php?title=Mamba3D_Configuration_Permanent_Future_Lab_Seats2meet.com_Utrecht_CS&oldid=1059"