Actions

Mamba3D Configuration Permanent Future Lab Seats2meet.com Utrecht CS

From Permanent Future Lab

Revision as of 12:31, 8 February 2017 by Jurjendevries (talk | contribs) (Created page with "Paste this into an config-bundle.ini file and import this in Repetier Slic3r. --- <nowiki> # generated by Slic3r 1.2.9 on Wed Feb 8 13:24:10 2017 [filament:ABS_1.75_w_Heated...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

Paste this into an config-bundle.ini file and import this in Repetier Slic3r. --- # generated by Slic3r 1.2.9 on Wed Feb 8 13:24:10 2017 [filament:ABS_1.75_w_HeatedBed] bed_temperature = 70 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_diameter = 1.75 first_layer_bed_temperature = 70 first_layer_temperature = 250 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 10 slowdown_below_layer_time = 20 temperature = 250 [filament:Flexible PLA] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 3 first_layer_bed_temperature = 0 first_layer_temperature = 240 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 slowdown_below_layer_time = 5 temperature = 240 [filament:High_Temp_PLA_1.75] bed_temperature = 70 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_diameter = 1.75 first_layer_bed_temperature = 75 first_layer_temperature = 210 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 10 slowdown_below_layer_time = 20 temperature = 205 [filament:Low_Temp_PLA_1.75] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.75 first_layer_bed_temperature = 0 first_layer_temperature = 195 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 slowdown_below_layer_time = 5 temperature = 200 [filament:PLA_1.75] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_diameter = 1.75 first_layer_bed_temperature = 0 first_layer_temperature = 195 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 10 slowdown_below_layer_time = 20 temperature = 195 [filament:PLA_1.75_w_HeatedBed] bed_temperature = 50 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_diameter = 1.75 first_layer_bed_temperature = 50 first_layer_temperature = 195 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 10 slowdown_below_layer_time = 20 temperature = 195 [filament:XT_1.75_w_HeatedBed] bed_temperature = 70 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_diameter = 1.75 first_layer_bed_temperature = 70 first_layer_temperature = 250 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 10 slowdown_below_layer_time = 20 temperature = 250 [filament:khalid] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 1 extrusion_multiplier = 1.01 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.75 first_layer_bed_temperature = 0 first_layer_temperature = 215 max_fan_speed = 100 min_fan_speed = 50 min_print_speed = 15 slowdown_below_layer_time = 15 temperature = 215 [filament:tst-filament-adhesion] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 3 first_layer_bed_temperature = 0 first_layer_temperature = 220 max_fan_speed = 70 min_fan_speed = 35 min_print_speed = 10 slowdown_below_layer_time = 5 temperature = 195 [filament:tst-luminous] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 3 first_layer_bed_temperature = 0 first_layer_temperature = 220 max_fan_speed = 70 min_fan_speed = 35 min_print_speed = 10 slowdown_below_layer_time = 5 temperature = 220 [presets] filament = PLA_1.75.ini print = 3_High_Res_Med_Speed.ini printer = Config_Mamba3D_AutoLevel.ini [print:1_Low_Res_Med_Speed] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 20 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_speed = 75% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 15% fill_pattern = line first_layer_acceleration = 0 first_layer_extrusion_width = 100% first_layer_height = 0.3 first_layer_speed = 30% gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 80 interface_shells = 0 layer_height = 0.295 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = nearest skirt_distance = 3 skirt_height = 1 skirts = 1 small_perimeter_speed = 50% solid_infill_below_area = 1 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 80% spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 40 support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 40 top_solid_layers = 4 travel_speed = 150 [print:2_Med_Res_Med_Speed] avoid_crossing_perimeters = 0 bottom_solid_layers = 4 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 20 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_speed = 75% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% fill_pattern = line first_layer_acceleration = 0 first_layer_extrusion_width = 100% first_layer_height = 0.3 first_layer_speed = 30% gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 80 interface_shells = 0 layer_height = 0.195 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = nearest skirt_distance = 3 skirt_height = 1 skirts = 1 small_perimeter_speed = 50% solid_infill_below_area = 1 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 80% spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 40 support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 40 top_solid_layers = 6 travel_speed = 150 [print:3_High_Res_Med_Speed] avoid_crossing_perimeters = 0 bottom_solid_layers = 5 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 20 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 75% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 20% fill_pattern = line first_layer_acceleration = 0 first_layer_extrusion_width = 100% first_layer_height = 0.25 first_layer_speed = 30% gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 2 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 80 interface_shells = 0 layer_height = 0.105 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = nearest skirt_distance = 3 skirt_height = 1 skirts = 1 small_perimeter_speed = 50% solid_infill_below_area = 1 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 80% spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 40 support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 70% top_solid_infill_speed = 40 top_solid_layers = 8 travel_speed = 150 xy_size_compensation = 0 [printer:Config_Mamba3D] bed_shape = 0x0,200x0,200x200,0x200 end_gcode = M104 S0 ; turn off temperature\nG1 X200 Y200 F4000\n;G28 X0 ; home X axis\nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 retract_before_travel = 2 retract_layer_change = 1 retract_length = 1 retract_length_toolchange = 0 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 25 start_gcode = M109 S[first_layer_temperature]\nG28\nG92 E0\nG1 E10 F100\nG1 Z5 F100\nG1 X0 Y0 F2500\nG1 Z0 F100\nG92 E0 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 vibration_limit = 0 wipe = 0 z_offset = 0 [printer:Config_Mamba3D_AutoLevel] bed_shape = 0x0,200x0,200x200,0x200 before_layer_gcode = end_gcode = M104 S0 ; turn off temperature\nG1 X200 Y200 F4000\n;G28 X0 ; home X axis\nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 octoprint_apikey = octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 1 retract_length_toolchange = 0 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 25 start_gcode = M109 S[first_layer_temperature]\nG91\nG1 Z10 F500\nG90\nG28 X0 Y0\nG1 X50 Y50 F2000\nG28 Z0\nG29\nG92 E0\nG1 Z10 F500\nG1 X0 Y0 F4000\nG1 Z0 F500\nG1 E20 F100\nG1 Z5 F100\nG1 X5 Y5 F2500\nG1 Z0 F100\nG92 E0 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = -0.95 [printer:Config_Mamba3D_concept] bed_shape = 0x0,200x0,200x200,0x200 before_layer_gcode = end_gcode = M104 S0 ; turn off temperature\nG1 X200 Y200 F4000\n;G28 X0 ; home X axis\nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 octoprint_apikey = octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 1 retract_length_toolchange = 0 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 30 start_gcode = M109 S[first_layer_temperature]\nG91\nG1 Z10 F500\nG90\nG28 X0 Y0\nG1 X50 Y50 F2000\nG28 Z0\nG29\nG92 E0\nG1 Z10 F500\nG1 X0 Y0 F4000\nG1 Z0 F500\nG1 E20 F100\nG1 Z5 F100\nG1 X5 Y5 F2500\nG1 Z0 F100\nG92 E0 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = -0.93 [printer:incheckpillar] bed_shape = 0x0,200x0,200x200,0x200 before_layer_gcode = end_gcode = M104 S0 ; turn off temperature\nG1 X200 Y200 F4000\n;G28 X0 ; home X axis\nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 octoprint_apikey = octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 1 retract_length_toolchange = 0 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 25 start_gcode = M109 S[first_layer_temperature]\nG28\nG92 E0\nG1 E10 F100\nG1 Z5 F100\nG1 X0 Y0 F2500\nG1 Z0 F100\nG92 E0 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = -1 [printer:khal] bed_shape = 0x0,200x0,200x200,0x200 before_layer_gcode = end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 octoprint_apikey = octoprint_host = pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 3 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0.1 retract_restart_extra_toolchange = 0 retract_speed = 30 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = 0 [settings] autocenter = 1 mode = expert